FANUC ALM共82篇
This section mainly introduces the alarms and detailed descriptions of each FANUC system. Through this section, you can find common alarm solutions.
Fanuc alarm: PS061 -P OR Q COMMAND IS NOT IN THE MULTIPLE REPETIVE CYCLES BLOCK-FANUC CNC

Fanuc alarm: PS061 -P OR Q COMMAND IS NOT IN THE MULTIPLE REPETIVE CYCLES BLOCK

Fanuc alarm: PS061 -P OR Q COMMAND IS NOT IN THE MULTIPLE REPETIVE CYCLES BLOCK CNC Machine Control Manufacturer:Fanuc Control Model:, 16i/18i/21i, 0i-A 0i-B 0I-D 0I-F 0I-F PLUS ...
share5的头像-FANUC CNC钻石会员share52个月前
8215
FANUC SP9009 OVERHEAT MAIN CIRCUIT-FANUC CNC

FANUC SP9009 OVERHEAT MAIN CIRCUIT

一、FANUC SP9009 Reason for alarm An abnormal rise in temperature of the spindle amplifier's heat sink or power element (IPM) was detected. 二、FANUC SP9009 troubleshooting If this...
share5的头像-FANUC CNC钻石会员share52个月前
05815
FANUC SP9019 EXCESS OFFSET CURRENT U-FANUC CNC

FANUC SP9019 EXCESS OFFSET CURRENT U

Amplifier alarm number: 19 FANUC SP9019 Reason for the alarm: Replace the Spindle Amplifier (SP) FANUC SP9019 Description Abnormality in a Spindle Amplifier(SP) component is detect...
share5的头像-FANUC CNC钻石会员share532天前
03515
Fanuc alarm: PS035 -CAN NOT COMMANDED G31-FANUC CNC

Fanuc alarm: PS035 -CAN NOT COMMANDED G31

Fanuc alarm: PS035 -CAN NOT COMMANDED G31 CNC Machine Control Manufacturer:Fanuc Control Model:, 16i/18i/21i, 0i-A 0i-B 0I-D 0I-F 0I-F PLUS Fanuc alarm: PS035 -CAN NOT COMMANDED ...
FANUC SP1220 spindleless amplifier-FANUC CNC

FANUC SP1220 spindleless amplifier

一、FANUC SP1220 Reason for alarm The cable connected to the serial spindle amplifier is disconnected, or the serial spindle amplifier has not been connected. 二、FANUC SP1220 trou...
Fanuc alarm: PS004 - ADDRESS NOT FOUND-FANUC CNC

Fanuc alarm: PS004 – ADDRESS NOT FOUND

Fanuc alarm: PS004 - ADDRESS NOT FOUND CNC Machine Control Manufacturer:Fanuc Control Model:, 16i/18i/21i, 0i-A 0i-B 0I-D 0I-F 0I-F PLUS PS004 - ADDRESS NOT FOUND Alarm Descripti...
share5的头像-FANUC CNC钻石会员share53个月前
07115
Fanuc alarm: PS025 -CIRCLE CUT IN RAPID (F0)-FANUC CNC

Fanuc alarm: PS025 -CIRCLE CUT IN RAPID (F0)

Fanuc alarm: PS025 -CIRCLE CUT IN RAPID (F0) CNC Machine Control Manufacturer:Fanuc Control Model:, 16i/18i/21i, 0i-A 0i-B 0I-D 0I-F 0I-F PLUS Fanuc alarm: PS025 -CIRCLE CUT IN R...
Fanuc alarm: PS027 -NO AXES COMMANDED IN G43/G44-FANUC CNC

Fanuc alarm: PS027 -NO AXES COMMANDED IN G43/G44

Fanuc alarm: PS027 -NO AXES COMMANDED IN G43/G44 CNC Machine Control Manufacturer:Fanuc Control Model:, 16i/18i/21i, 0i-A 0i-B 0I-D 0I-F 0I-F PLUS Fanuc alarm: PS027 -NO AXES COM...
Steps to resolve illegal FANUC SV417 servo parameters-FANUC CNC

Steps to resolve illegal FANUC SV417 servo parameters

SV417 servo parameter setting error, solution and steps are as follows: Solution: (1) Diagnosis data No.203 # 4=0: The parameters detected by CNC are illegal. Details confirm diagn...
share5的头像-FANUC CNC钻石会员share540天前
05814