FANUC ALM共82篇 第3页
This section mainly introduces the alarms and detailed descriptions of each FANUC system. Through this section, you can find common alarm solutions.
FANUC SP9018 SUMCHECK ERROR PROGRAM ROM-FANUC CNC

FANUC SP9018 SUMCHECK ERROR PROGRAM ROM

Amplifier alarm number: 18 FANUC SP9018 Reason for the alarm: The spindle amplifier data ROM component is abnormal. Troubleshooting ideas:Replace the Spindle Amplifier (SP) control...
share5的头像-FANUC CNC钻石会员share51个月前
0805
FANUC SP9017 Serial spindle alarm-FANUC CNC

FANUC SP9017 Serial spindle alarm

Amplifier alarm number: 17 FANUC SP9017 Reason for the alarm: An abnormality in the spindle amplifier ID was detected. Troubleshooting ideas:Replace the spindle amplifier. FANUC SP...
share5的头像-FANUC CNC钻石会员share51个月前
05412
FANUC SP9016 RAM ERROR-FANUC CNC

FANUC SP9016 RAM ERROR

Amplifier alarm number: 16 FANUC SP9016 Reason for the alarm: The RAM used for external data in the spindle amplifier is abnormal. Troubleshooting ideas: The hardware is damaged, r...
share5的头像-FANUC CNC钻石会员share51个月前
04412
FANUC SP9015 SPINDLE SWITCHING FAULT-FANUC CNC

FANUC SP9015 SPINDLE SWITCHING FAULT

Amplifier alarm number: 15 FANUC SP9015 Reason for the alarm: Caused by abnormal sequence during spindle switching/output switching. Troubleshooting ideas: 1) An alarm is issued wh...
share5的头像-FANUC CNC钻石会员share51个月前
06512
FANUC SP9014 SOFTWARE SERIES MISMATCH-FANUC CNC

FANUC SP9014 SOFTWARE SERIES MISMATCH

Amplifier alarm number: 14 FANUC SP9014Reason for the alarm: Using an amplifier that has not been logged in to the spindle software. Troubleshooting ideas: The spindle data was mis...
share5的头像-FANUC CNC钻石会员share51个月前
0407
FANUC SP9013 CPU DATA MEMORY FAULT-FANUC CNC

FANUC SP9013 CPU DATA MEMORY FAULT

Amplifier alarm number: 13 FANUC SP9013 Reason for the alarm: The spindle amplifier control circuit is abnormal. Troubleshooting ideas: Confirm that the hardware is damaged and rep...
share5的头像-FANUC CNC钻石会员share51个月前
03713
FANUC SP9012 OVERCURRENT POWER CIRCUIT-FANUC CNC

FANUC SP9012 OVERCURRENT POWER CIRCUIT

Amplifier alarm number: 12 Reason for the alarm: Caused by excessive current in the spindle motor. FANUC SP9012 Troubleshooting ideas: 1) Check the initialization of the inherent p...
FANUC SP1220 spindleless amplifier-FANUC CNC

FANUC SP1220 spindleless amplifier

一、FANUC SP1220 Reason for alarm The cable connected to the serial spindle amplifier is disconnected, or the serial spindle amplifier has not been connected. 二、FANUC SP1220 trou...
FANUC SP9011 SSPA:11 DC LINK overvoltage-FANUC CNC

FANUC SP9011 SSPA:11 DC LINK overvoltage

FANUC SP9011 Reason for alarm The voltage of the DC section (DC bus section) of the main circuit has increased abnormally. FANUC SP9011 troubleshooting This alarm occurs when the ...
share5的头像-FANUC CNC钻石会员share52个月前
05712