FANUC ALM共82篇
This section mainly introduces the alarms and detailed descriptions of each FANUC system. Through this section, you can find common alarm solutions.
Fanuc alarm: PS009 -IMPROPER NC-ADDRESS-FANUC CNC

Fanuc alarm: PS009 -IMPROPER NC-ADDRESS

Fanuc alarm: PS009 -IMPROPER NC-ADDRESS CNC Machine Control Manufacturer:Fanuc Control Model:, 16i/18i/21i, 0i-A 0i-B 0I-D 0I-F 0I-F PLUS Fanuc alarm: PS009 -IMPROPER NC-ADDRESS ...
Fanuc alarm: PS058 -END POINT NOT FOUND-FANUC CNC

Fanuc alarm: PS058 -END POINT NOT FOUND

Fanuc alarm: PS058 -END POINT NOT FOUND CNC Machine Control Manufacturer:Fanuc Control Model:, 16i/18i/21i, 0i-A 0i-B 0I-D 0I-F 0I-F PLUS Fanuc alarm: PS058 -END POINT NOT FOUND ...
SV417 parameter illegal, diagnostic number 6402-FANUC CNC

SV417 parameter illegal, diagnostic number 6402

Problem phenomenon: SV417 parameter illegal when configuring grating ruler Solution: The value in diagnostic number 352 is 6402 Clear the relevant parameters of the fifth group of ...
share5的头像-FANUC CNC钻石会员share537天前
0619
Fanuc alarm: PS031 -ILLEGAL P COMMAND IN G10-FANUC CNC

Fanuc alarm: PS031 -ILLEGAL P COMMAND IN G10

Fanuc alarm: PS031 -ILLEGAL P COMMAND IN G10 CNC Machine Control Manufacturer:Fanuc Control Model:, 16i/18i/21i, 0i-A 0i-B 0I-D 0I-F 0I-F PLUS Fanuc alarm: PS031 -ILLEGAL P COMMA...
FANUC SP9006 THERMAL SENSOR DISCONNECT-FANUC CNC

FANUC SP9006 THERMAL SENSOR DISCONNECT

FANUC SP9006 Reason for alarm An abnormality in the temperature sensor inside the spindle motor or a disconnection of the temperature sensor cable was detected. FANUC SP9006 troubl...
share5的头像-FANUC CNC钻石会员share52个月前
011910
Fanuc alarm: PS048 -BASIC 3 AXIS NOT FOUND-FANUC CNC

Fanuc alarm: PS048 -BASIC 3 AXIS NOT FOUND

Fanuc alarm: PS048 -BASIC 3 AXIS NOT FOUND CNC Machine Control Manufacturer:Fanuc Control Model:, 16i/18i/21i, 0i-A 0i-B 0I-D 0I-F 0I-F PLUS Fanuc alarm: Fanuc alarm: PS048 -BASI...
FANUC SP9017 Serial spindle alarm-FANUC CNC

FANUC SP9017 Serial spindle alarm

Amplifier alarm number: 17 FANUC SP9017 Reason for the alarm: An abnormality in the spindle amplifier ID was detected. Troubleshooting ideas:Replace the spindle amplifier. FANUC SP...
share5的头像-FANUC CNC钻石会员share51个月前
05412
Fanuc alarm: PS010 -IMPROPER G-CODE-FANUC CNC

Fanuc alarm: PS010 -IMPROPER G-CODE

Fanuc alarm: PS010 -IMPROPER G-CODE CNC Machine Control Manufacturer:Fanuc Control Model:, 16i/18i/21i, 0i-A 0i-B 0I-D 0I-F 0I-F PLUS Fanuc alarm: PS010 -IMPROPER G-CODE Alarm De...
Fanuc alarm: PS060 -SEQUENCE NUMBER NOT FOUND-FANUC CNC

Fanuc alarm: PS060 -SEQUENCE NUMBER NOT FOUND

Fanuc alarm: PS060 -SEQUENCE NUMBER NOT FOUND CNC Machine Control Manufacturer:Fanuc Control Model:, 16i/18i/21i, 0i-A 0i-B 0I-D 0I-F 0I-F PLUS Fanuc alarm: PS060 -SEQUENCE NUMBE...